-
The XTENDEX® 4K 18Gbps HDMI Extender Over IP via Fiber Optic Cable locates an Ultra-HD 4Kx2K 60Hz 4:4:4 HDMI display, audio, IR, and RS232 up to 24.8 miles (40 kilometers) away from an HDMI source using a single LC singlemode fiber optic strand or 1,640 feet (500 meters) using LC multimode fiber optic cable.
Each 4K 18Gbps HDMI Extender Over IP consists of a local unit that connects to an HDMI source and a local display via the HDMI loop output, and a remote unit that connects to an HDMI display. The local and remote units can be connected together for a Point-to-Point connection via Fiber Optic Cable or a Point-to-Many connection via a 10G SFP network switch. Support for multiple transmitters requires a managed 10G SFP network switch.
-
- Signal transmission via single-strand LC fiber optic cable ;
Using singlemode 9-micron cable, extend to 24.8 miles (40 km) ;
Using 50-micron OM2 (or better) multimode cable, extend to 1,640 feet (500 meters) ;
Zero latency
-
Supports Ultra-HD 4Kx2K resolutions to 3840x2160 and 4096x2160 @60Hz YUV 4:4:4, HDTV resolutions to 1080p @60Hz, and up to 1920x1200 (WUXGA).
-
Cascade network switches to extend the length longer distances.
-
Up to 12 switches can be cascaded.
-
HDMI features supported:
HDMI 2.0 ;
8-bit, 10-bit, and 12-bit Deep Color ;
Dolby TrueHD, DTS-HD Master Audio, Dolby Digital, Dolby Digital+, Dolby Atmos, LPCM 7.1CH, DTS 5.1, and DTS:X ;
RGB, YCbCr 4:4:4, YCbCr 4:2:2, and YCbCr 4:2:0 ;
Bandwidth up to 600 Mhz (18Gbps) ;
3D (1080p @60Hz)
-
Support for CEC (consumer electronic control) compatible devices.
-
HDR10
-
ARC
-
HDCP 2.2 and 1.4 compliant.
-
Supports local and remote HDMI displays.
-
For a point-to-many connection, a standalone network with an unmanaged 10G SFP network switch, hub, or router can be used instead of a managed SFP network switch.
-
Easily expandable. Add remote units as you add monitors.
-
Up to 255 receivers supported.
-
It is not recommended to use any other network devices on this standalone network as it may cause degradation in performance.
-
Support for multiple transmitters (many-to-many connection) requires a managed 10G SFP network switch with IGMP support and Jumbo frame support. Standard LAN switches can only support one transmitter.
-
The managed 10G SFP network switch must support port-based IEEE 802.1Q VLAN.
-
Each VLAN acts as a separate HDMI Over IP Channel on the network.
-
Each VLAN channel supports one transmitter.
-
The number of local and remote units that can be used is dependent on the backplane bandwidth of the switch.
-
Plug and play installation allows receivers to find the transmitters automatically on the same subnet.
-
Local and remote units must be in the same LAN. The units do not support WAN connections.
-
Built-in default EDID table.
-
Supports full-duplex RS232 up to 115200 baud.
-
Bi-directional IR control from input and output locations.
-
Supports HDMI embedded digital audio and ARC audio extraction via Toslink connection.
-
Built-in surge and ESD protection.
-
Mounting brackets included for easy surface/wall mounting.
- Product Datasheet
-
-
Local Unit
-
One female HDMI connector for source connection.
-
One female HDMI connector for local display.
-
Supports Ultra-HD 4Kx2K resolutions to 3840x2160 and 4096x2160 @60Hz YUV 4:4:4, HDTV resolutions to 1080p @60Hz, and up to 1920x1200 (WUXGA).
-
Supports embedded digital audio.
-
Two 3.5mm ports connecting an IR emitter and receiver (included).
-
IR frequency range: 20 to 60 kHz.
-
3-pin screw terminal for RS232.
-
Supports full-duplex RS232 up to 115200 baud.
-
One TOSLINK optical port for HDMI ARC audio extraction
-
One simplex LC fiber optic port for sending/receiving video/audio, IR, and RS232 signals.
-
One female USB Micro Type B connector for firmware updates.
-
Supports HDCP 2.2 and 1.4.
-
Remote Unit
-
One female HDMI connector for display.
-
Supports Ultra-HD 4Kx2K resolutions to 3840x2160 and 4096x2160 @60Hz YUV 4:4:4, HDTV resolutions to 1080p @60Hz, and up to 1920x1200 (WUXGA).
-
Supports embedded digital audio.
-
Two 3.5mm ports connecting an IR emitter and receiver (included).
-
IR frequency range: 20 to 60 kHz.
-
3-pin screw terminal for RS232.
-
Supports full-duplex RS232 up to 115200 baud.
-
One TOSLINK optical port for SPDIF digital audio.
-
One simplex LC fiber optic port for sending/receiving video/audio, IR, and RS232 signals.
-
One female USB Micro Type B connector for firmware updates
-
Supports HDCP 2.2 and 1.4.
Power
-
Local and remote unit:
Input: 100 to 240 VAC at 50 or 60Hz via AC adapter. (Country-specific power supplies included.)
-
Output:
US power supply: 5VDC, 2A ;
UK, EU, AUS power supplies: 5VDC, 3A
-
Power consumption:
Local unit: 4.6W ;
Remote unit: 4.1W
-
Dimensions
WxDxH (in): 4.88x4.54x1.18 (124x115x30 mm)